Best Way To Study For EMC D-PEMX-DY-23 Exam Brilliant D-PEMX-DY-23 Exam Questions PDF
Updated Verified Pass D-PEMX-DY-23 Exam - Real Questions and Answers
NEW QUESTION # 73
What is the maximum supported drive configuration on a PowerEdge MX840c compute sled?
- A. 2 x 2.5" drives and 4 x 3.5" drives
- B. 6 x 3.5" drives
- C. 8 x 2.5" drives
- D. 4 x 2.5" drives and 2 x 3.5" drives
Answer: C
NEW QUESTION # 74
Once power is applied to the chassis, what is the next sequence after MM completes booting?
- A. Load the LCD panel.
- B. MM uboot starts.
- C. PSU firmware starts.
- D. 12 V DC Rail on.
Answer: A
NEW QUESTION # 75
What is the port configuration of the MX9116n FSE?
- A. 32 internal 25 GbE server facing ports
10 QSFP28-DD ports
4 100 GbE QSFP28 uplink ports
2 100 GbE QSFP28 unified ports - B. 32 internal 25 GbE server facing ports
12 QSFP28-DD ports
2 100 GbE QSFP28 uplink ports
2 100 GbE QSFP28 unified ports - C. 16 internal 25 GbE server facing ports
10 QSFP28-DD ports
4 100 GbE QSFP28 uplink ports
2 100 GbE QSFP28 unified ports - D. 16 internal 25 GbE server facing ports
12 QSFP28-DD ports
2 100 GbE QSFP28 uplink ports
2 100 GbE QSFP28 unified ports
Answer: D
NEW QUESTION # 76
When a SAS IOM is power cycled, how much time does it take for the storage-IOM to display mapping information?
- A. 300 seconds
- B. 500 seconds
- C. 400 seconds
- D. 600 seconds
Answer: A
NEW QUESTION # 77
An implementation engineer prepares to install a PowerEdge MX7000.
Which serial cable do they use?
- A. USB-A --> Micro USB-B
- B. DB9 --> Micro DB9
- C. USB-A --> USB-B
- D. DB9 --> DB9
Answer: A
NEW QUESTION # 78
Refer to the exhibit.
How many internal server-facing ports are available on this I/O module for the MX7000 chassis?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION # 79
Which feature in OpenManage Mobile can be used to allow the monitoring of a PowerEdge MX7000 chassis?
- A. OIDC provider
- B. OpenManage Essentials
- C. Augmented Reality
- D. Redfish Provider
Answer: C
NEW QUESTION # 80
What location allows an administrator to enable DHCP for every iDRAC in the MX7000?
- A. Chassis Group Home Page > Compute > iDRAC Networking
- B. Chassis Landing Page > Settings > Network > iDRACs
- C. Chassis Landing Page > Settings > Quick Deploy
- D. Chassis Landing Page > Devices > Compute
Answer: C
NEW QUESTION # 81
Which VLAN is reserved for internal switch communication?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 82
How can a hard reset be performed on iDRAC?
- A. Using the OME-M Interface and selecting Virtual Reseat
- B. On the iDRAC web interface, select the Reset option
- C. On the server, press and hold the ID LED button for 15 seconds
- D. Using the RACADM command --SystemReset -t 0 -f
Answer: C
NEW QUESTION # 83
What is a benefit of SmartFabric Services Mode?
- A. Automatic detection of packet collisions
- B. Load balancing for application layers
- C. Load balancing for management layers
- D. Topology validation and self-healing
Answer: C
NEW QUESTION # 84
A company receives their first MX7000 chassis. They connect all the provided power supply cables into two different PDUs on different power grids for redundancy. Each of the six power supplies is cabled and has green LEDs. One Management Module is present along with all system fans. Grid redundancy is configured as the power redundancy mode.
The chassis is fully populated with six compute sleds and one IOM but only two of the six sleds will power on.
What is the possible reason for this issue?
- A. Mixed high line and low line AC inputs in the same chassis is not supported.
- B. An additional IOM is required to power on and manage the remaining sleds.
- C. Two Management Modules are required to power on the populated chassis.
- D. Power supply unit redundancy policy was not used.
Answer: D
NEW QUESTION # 85
Refer to the exhibit.
A customer recently replaced all the dual-port network cards in mezzanine A with quad-port network cards across all 16 PowerEdge MX740c sleds in the two-chassis configuration. The customer can only access half of the network ports, even though the quad-port cards are visible in the iDRAC.
What actions are required to resolve the problem?
- A. Reseat all the switches.
Adjust the switch configuration to use the new ports. - B. Install a new 200G cable from port 3 on the MX7116n in chassis 2 slot A1 into port 19 on the MX9116n in chassis 1 slot A1.
Do the same for the switches in slots A2.
Adjust the switch configuration to use the new ports. - C. Reboot the switches.
Adjust the switch configuration to use the new ports. - D. Do a virtual reseat of all the MX740c sleds.
Update the firmware on all the quad port network cards.
Adjust the switch configuration to use the new ports.
Answer: B
NEW QUESTION # 86
What item is used to refer to a daisy-chained configuration of a multiple MX7000 chassis environment?
- A. Identity group
- B. Wired group
- C. Physical group
- D. Chassis group
Answer: B
NEW QUESTION # 87
Refer to the exhibit.
What is shown?
- A. MX5108n
- B. MXG610s
- C. MX5000s
- D. MX5016s
Answer: D
NEW QUESTION # 88
What are the components of the control panel of a PowerEdge MX750c sled?
- A. Power button
USB 3.0 port
iDRAC micro port
iDRAC direct status LED - B. Power button
USB 3.0 port
micro DisplayPort
iDRAC direct status LED - C. Power button
USB 2.0 port
iDRAC micro port
iDRAC direct status LED - D. Power button
USB 2.0 port
micro DisplayPort
iDRAC direct status LED
Answer: A
NEW QUESTION # 89
Which two main components comprise a Scalable Fabric?
- A. MX7116n and the MX5108n
- B. MX9116n and the MX7116n
- C. MX9116n and the 25GbE PTM
- D. MX9116n and the MX5108n
Answer: B
NEW QUESTION # 90
What can be used as the firmware update source for OME-M within an MX chassis?
- A. Dell Update Package
Baseline from a Catalog - B. Server Update Utility
Baseline from a Catalog - C. Dell Update package
System Live Image (SLI) - D. Server Update Utility
System Live Image (SLI)
Answer: A
NEW QUESTION # 91
What is a characteristic of MX7000 networking in Full Switch Mode?
- A. Layer 2 bridging is disabled by default and interfaces must join a bridge domain (VLAN) before being able to forward frames.
- B. Networking is enabled by default and all switch-specific OS10EE capabilities are available.
- C. Switches operate as layer 2 I/O aggregation devices and are managed through OME-M.
- D. Networking is available on MX9116n FSE and MX7116n FEM but not on the MX5108n.
Answer: B
NEW QUESTION # 92
What feature does OME-M v1.3 provide when replacing the Right Control Panel?
- A. MCM configuration can be backed up in the cloud.
- B. Chassis configuration must be reconfigured.
- C. MCM configuration must be reconfigured.
- D. Chassis configuration is maintained.
Answer: D
NEW QUESTION # 93
Which statement describes L2 Multicast as implemented on the PowerEdge MX7000 IOM?
- A. MLD snooping controls the flooding of IPv6 multicast traffic on VLANs while the IGMP limits the flooding of IPv4 multicast traffic.
- B. MLD snooping and IGMP control or limit the flooding of IPv4 multicast traffic on VLANs.
- C. MLD snooping controls the flooding of IPv4 multicast traffic on VLANs while the IGMP limits the flooding of IPv6 multicast traffic.
- D. MLD snooping and IGMP control or limit the flooding of IPv6 multicast traffic on VLANs.
Answer: A
NEW QUESTION # 94
......
Updated PDF (New 2024) Actual EMC D-PEMX-DY-23 Exam Questions: https://troytec.getvalidtest.com/D-PEMX-DY-23-brain-dumps.html